null

Turbelle e-jet 5005

SKU:
HGHG-TUN5005.000
(No reviews yet) Write a Review
$213.05

About This Product

Turbelle e-jet

Turbelle e-jet 5005 is a pump operated on safety extra-low voltage, the speed of which can be controlled electronically. It is ideal for the simulation of lapping waves or tidal currents in every aquarium. It contains a new microprocessor-controlled motor and thus can be called an intelligent pump:
The electronic motor adapts its speed automatically to the pump load and always seeks the best efficiency at the lowest possible consumption of energy. This energy consumption is about fifty per cent lower than in conventional pump motors.
The pump will be stopped immediately in case of blockage. After the blockage has been removed, the pump will start up automatically after a delay of 20 seconds.
Turbelle e-jet 5005 has been provided with a fish care function, which causes a revolution of the screw every twenty seconds.
This pump can be controlled by Multicontroller 7094, 7095 and 7096 as well as by Singlecontroller 7091; and is supplied with a power supply unit.

Turbelle e-jet 5005 replaces two pumps !

Turbelle e-jet 5005 has been fitted with a power supply unit (article No. 6101.240) with two adjustment possibilities set by the lateral jumper.
Adjustment to 24 V direct current (delivery condition):
Pump adjustable from 2,400 l/h to 4,200l/h (634 to 1,109.5 USgal./h); energy consumption: max. 40 W.
Adjustment 15 V direct current: Pump adjustable from 1,600 l/h to 2,800 l/h (422.7 to 739.7 USgal./h); energy consumption: max. 20 W.
The adjustment of 15 V or 24 V is very simple by setting the jumper at the bottom of the power supply unit.

Turbelle e-jet 5005 as a high-pressure pump; Hmax. 5,5 m (216.5 in.).

With a few addtional parts only the Turbelle e-jet 5005 can be converted into a high-pressure pump. After conversion, the pump can serve as a recirculation pump for special applications with high water columns or into a skimmer pump for a Venturi skimmer. The following parts have to be used to replace the drive unit and the impeller housing:
Impeller Housing 1201.13, Drive Unit 1205.700, and Sleeve 1200.15.
Thus, the Turbelle e-jet 5005 achieves the following performance:
Adjustment to 24 V direct current:
(delivery condition):
Pump adjustable between 800 and 1,400 l/h (211.3 and 369.8 USgal./h); Hmax. 5.5 m (216.5 in.); energy consumption max. 40 W.
Adjustment 15 V direct current:
Pump adjustable between 550 and 900 l/h (145.3 and 237.7 USgal./h); Hmax. 3 m (118.1 in.); energy consumption max. 19 W.
The adjustment of 15 V or 24 V is very simple by setting the jumper at the bottom of the power supply unit.

Turbelle e-jet 5005

Flow rate at 15 V: 1,600 to 2,800 l/h (422.7 to 739.7 USgal./h)
Flow rate at 24 V: 2,400 to 4,200 l/h (734 to 1,109.5 USgal./h)
Hmax. at 15 V: 1.2 m (47.2 in.)
Hmax. at 24 V: 2.2 m (89.6 in.)
Energy consumption at 15 V: max. 20 W
Energy consumption at 24 V: max. 40 W
Voltage / frequency: 100 240 V / 50 60 Hz
Cable length: 5 m (196.8 in.)
Dimensions: diam. 98 x 100 mm (3.8 x 3.9 in.)
Inlet: diam. 25 mm (.98 in.) / Outlet: diam. 25 mm (.98 in.)
Magnet holder up to a glass thickness of 19 mm (.74 in.)